Overview – PrusaSlicer 2.5 – 3D PRINTING UK


PrusaSlicer 2.5

A slicer is without doubt one of the most necessary instruments for 3D printing, and I often depend on the wonderful Ultimaker Cura. This is without doubt one of the hottest slicers round, for good motive, however there are options. This week I’ve been enjoying with one in every of them – PrusaSlicer 2.5.

So What Is It?

Prusa Analysis is a well-recognized title for 3D printer fans. The Czech-based firm is well-known for its basic i3 printer, and it additionally has its personal slicer. That is bundled with Prusa printers, however you can too obtain it from their web site – and that’s precisely what I did.

I’ve seen a couple of horrible slicers, together with some that aren’t even absolutely translated into English, and PrusaSlicer undoubtedly isn’t a kind of. Set up is slick {and professional}, and whenever you open it for the primary time it launches straight right into a configuration wizard. Straight away it provides you the selection of setting it up for printers from different distributors, and gives a protracted checklist of 3D printer producers. I chosen Creality, and acquired a really complete collection of fashions with the Ender 3 proper on the high. All I needed to do was choose the printer and click on End so as to add an Ender 3 profile to the slicer.

Does It Work?

With PrusaSlicer set as much as create G-code for my 3D printer, I went searching for one thing to slice. I’ve simply been utilizing Cura to slice a jig that I made for a DIY mission, so I made a decision to make use of that for a direct comparability. Getting it loaded took a few minutes, as a result of I’m used to Cura asking to open a file; on PrusaSlicer you could import it. As soon as that was executed, I went to work on establishing the print precisely the identical as I had in Cura.

That is the place issues began to get somewhat tough. The fundamental PrusaSlicer interface may be very clear and effectively laid out. There’s a sensible picture of the print mattress, which seems to be nicer than Cura’s wireframe model however lacks the useful grid traces I’m used to. Key print settings are in a separate panel down the best of the display which has Easy, Superior and Knowledgeable modes (though there isn’t actually a lot distinction). For an easy print it’s very simple to make use of.

Sadly the print I wished to arrange isn’t fully simple. As a result of I’m printing a jig, which might’t be distorted in any respect, construct plate adhesion is essential. In Cura I set it as much as print on a reasonably large raft, which is well executed within the Adhesion part of the drop down menu. The issue is that in PrusaSlicer there’s no raft choice within the panel. I ultimately discovered it by rummaging round within the Print Settings tab, the place it seems that rafts are an choice in Help quite than Adhesion. Once I did discover it there have been sufficient choices to arrange the raft I used to be searching for, however nowhere close to as many as Cura has.

PrusaSlicer 2.5 v Ultmaker Cura

Cura (on the best) has much more setting choices obtainable.

Regardless of having the identical settings in each slicers, together with the identical speeds – 25mm/s for partitions, and 50mm/s for the 50% cubic infill – I acquired distinctly completely different outcomes. Cura predicted 7hr 45min for the job, with 81g of filament used; PrusaSlicer got here in at 7hr 13min and 83.2g. Nonetheless, the code generated by each slicers labored effectively, with no seen high quality distinction between the ultimate prints.

The Verdict

PrusaSlicer 2.5 is a free obtain, obtainable as a part of Prusa’s driver and app bundle. Its interface is clear and intuitive, though there’s a little bit of a studying curve if you happen to’re used to Cura. For instance, in Cura you maintain the best mouse button if you wish to pan the view round; in PrusaSlicer you could maintain the left mouse button. Total, although, it’s simple to arrange and straightforward to make use of.

My private opinion is that PrusaSlicer 2.5 might be a barely higher choice than Cura if you happen to don’t fiddle with settings an excessive amount of. Its primary settings are very simple to search out due to that massive, clear panel, and clicking on the Print Settings tab provides you with entry to much more. Then again, if you need final management over your settings, at the price of every part being loaded into one huge drop-down menu, Cura nonetheless has an edge.



Source_link

Leave a Reply

Your email address will not be published.